Tekdis Products

VMC100 - 7" ARM AIO


Downloads

General

Cooling System: Fanless

Enclosure: Plastic PC + ABS

Mounting: Support VESA 75, stand mounting

Four SMA Type antenna connectors of BT/Wi-Fi /WWAN/GPS

Power Input: 9 ~ 36VDC input with Ignition

Power Consumption: 15W

Ingress Protection: Front panel IP54

Dimension: 213mm (W) x 145mm (H) x 50mm (D)(8.3" x 5.7" x 1.9")

Weight: TBD

LCD Panel

7-inch TFT LCD Panel with LED Backlight 800 x 480 pixels (WVGA) Brightness: 400 cd/m² (typical)

Contrast ratio: 600:1 (typical)

Touch Screen Sensor

4-wire resistant touch Anti-glare coating surface Transmission rate: 78 ± 3%

CPU & Chipset

On-board DDR3 512MB

Expandable Storage

1 x Micro SDHC Slot (Bundle with 8GB)

Expansion

1 x Pin Head for WLAN option

1 x mini-PCIe socket ((USB + UART) for WWAN option) OBD option and support protocols
- ISO 15765-4, ISO 14230-4, ISO 9141-2, SAE J1850
- ISO 15765, ISO 11898
- SAE J1939
Battery module option

I/O Interface-Front

F1 ~ F5 functions key Light Sensor Internal Mic-in

2 x Built-in 2W speakers

3 x LED indicators (Power mode, Storage and WWAN status)

I/O Interface-Lateral

Right side
- 1 x Micro SD card socket
- 1 x SIM card socket
- 1 x USB 2.0 host type A connector
- 1 x Mic-in, Line-out
Left side
- 1 x Power button
- 1 x System reset button
- Volume up/down or Brightness up/dow

I/O Interface-Rear

1 x 5-pin Circular connector for Power/Ignition input

1 x RJ45 for LAN

1 x RJ45 for Full RS-232 with 0V/5V/12V power supply (0.5A)

1 x DB9 (Male) for
- RX/TX or RS-485
- 2 x CAN Bus 2.0
1 x DB15 (Female) for
- GPS dead reckoning interface (optional)
- 3 x GPO, 3 x GPI

Communication Module

1 x On board GPS module

1 x WLAN or Bluetooth module for optional

1 x WWAN module for optional

Power Management

Selectable boot-up & shut-down voltage for low power protection HW design ready for 8-level delay time on/off at user's self configuration Power on/off ignition, software detectable

Operating System

Linux Ubuntu (kernel V3.2.0)

Environment

Operating temperatures: Ambient with air -20°C to 60°C ŒŒ

Storage temperatures: -30°C to 80°C

Relative humidity: 10% to 90% (non-condensing)

Vibration (random): 3g @5 ~ 500Hz Vibration
Operating: MIL-STD-810G, 514.6 Procedure 1, Category 4
Storage: MIL-STD-810G, 514.6 Procedure 1, Category 24
Shock
Operating: MIL-STD-810G, Method 516.6, Procedure I, trucks and semi-trailers=20g
Crash hazard: MIL-STD-810G, Method 516.6, Procedure V, ground equipment=75g

Power Design & Protection

Load dump and inductive load protection Cold cranking protection Transient voltage protection Electrostatic discharge protection

Standards/Certifications

EMC
- CE, FCC class B
Power
- SAE J1113
- SAE J1455
- ISO 7637-2
Safety
- EN 60950-1 LVD

Ask about this product

Comments